Wet Mop Head in Polyester Terry Towel Strips With Custom 150-350g Weight For Daily Floor Cleaning in Hotels And Supermarkets

Wet Mop Head in Polyester Terry Towel Strips With Custom 150-350g Weight For Daily Floor Cleaning in Hotels And Supermarkets
Product Introduction:
This is a cut-end mop head made from polyester terry towelling — either 100% polyester or a polyester-nylon blend. It is a replacement head for wet floor cleaning, and it fits mop handles that take an Italian thread, French thread or other threaded socket. Every head can be made from 150 g to 350 g, and in the colour you specify.
Send Inquiry
Description
Technical Parameters
Material
100% polyester, or polyester-nylon blend
Construction
Terry towelling cut into strips (cut end)
Weight
150 g – 350 g, made to order
Colour
Custom, matched to your colour reference
Socket
Italian thread, French thread, others on request

Why buyers choose this terry mop head

Cut-end strips. The terry is cut into individual strips rather than looped, so the head moves freely across tile and grout lines without the strips catching.

A weight for every floor. From 150 g for light, small-area work up to 350 g for large commercial floors - you pick the weight, not the other way round.

Polyester terry holds up wet. Polyester keeps its strength when soaked, and it resists the mildew and rot that shorten the life of cotton heads left damp overnight.

Colour used as a system. Custom colour lets you run zone-coded cleaning - one colour per area - instead of relying on staff memory.

A socket that matches your handle. Italian thread and French thread are both available, so the head fits the handles you already own instead of forcing a new handle purchase.

What it is made of

The head is built from polyester terry towelling - the same looped-fabric structure used in towelling, cut into strips and assembled onto a threaded socket.

100% polyester

The standard build. Fast-drying, mildew-resistant, and it keeps its strength when wet.

Polyester-nylon blend

Add nylon when the floor is abrasive (concrete, quarry tile, non-slip coatings) or when the head is expected to run heavy daily hours. Nylon is the fibre that carries abrasion resistance in a blend.

Neither option is cotton and neither is microfibre. If you are replacing a cotton head, expect a different feel: this head wrings out lighter and dries far faster, but a cotton head of the same weight will pick up more water.

Cut end or loop end?

This head is cut end: the terry strips are cut, not looped.

Type Behaviour
Cut end Strips move independently, so the head follows tile and grout lines and gets into irregular flooring. In the first washes a cut-end head can shed a little loose fibre; this settles quickly.
Loop end Strips are closed loops, so there are no cut fibre ends to shed, and the head is generally specified where lint control matters most.

If your site or contract specifies loop end, ask us - the same weight and colour range is available in loop end.

Which thread do you need - Italian or French?

The thread is the screw fitting that joins the mop head to the handle. Fit the wrong one and the head simply will not sit tight.

Thread Fit
Italian thread Common on Italian and southern-European mop handles
French thread Common on French and other western-European handles
Other American thread and other specifications on request

How to check what you have: unscrew the current head and look at the male thread on the handle. Compare it against a known Italian or French thread, or send us the handle's thread diameter and we will match it. Buying handles and heads from the same supplier is the simplest way to avoid a mismatch.

Choosing a weight: 150 g to 350 g

Heavier is not automatically better. Weight buys you water capacity and wear life, and it costs you wringing effort and drying time.

Weight Typical use
150 – 200 g Small areas, quick spot work, light daily dust-and-damp passes
200 – 250 g General daily floor cleaning - offices, retail, smaller kitchens
250 – 300 g Larger floors and heavier soiling - restaurants, supermarkets, corridors
300 – 350 g High-traffic commercial and industrial floors, extended shifts

Most buyers find that one mid-range weight (around 250 g) covers the majority of their floors, and lighter or heavier heads are used for specific areas. Tell us the floor area, the soiling level and who does the wringing, and we will suggest a starting weight.

Material comparison

  100% Polyester Terry Polyester-Nylon Blend Cotton
Water pick-up per gram Moderate Moderate Higher
Drying time Fast Fast Slow
Strength when wet Retains Retains Loses
Mildew / rot risk if left damp Low Low High
Abrasion resistance Moderate Higher Lower
Wringing effort Lighter Lighter Heavier
Best for All-round wet cleaning Abrasive or high-hour floors Maximum water pick-up

Read the table honestly: if your only priority is the most water per gram, cotton still wins. Polyester terry is specified when drying time, odour control, head life and wringing effort matter - which in commercial cleaning is most of the time.

Colour coding: one colour per zone

Colour choice is not decoration. In food service and healthcare, cleaning equipment is commonly colour-coded so that a head used in one area is never used in another.

Colour Zone
Red Toilets, urinals, high-risk sanitary areas
Blue General areas, offices, corridors
Green Kitchens and food-preparation areas
Yellow Washrooms, basins, low-risk sanitary
[YOUR OTHER COLOUR] [YOUR ZONE SPLIT]

Tell us the colour and we match it. Colour coding is a housekeeping control - it is not a certification, and this page makes no antimicrobial or hygiene-certification claim for the head itself.

Care and replacement

Rinse in clean water after each shift. Most of the odour in a mop head is soil sitting in the fabric, not the fabric itself.

Wash warm when the head needs it.

Do not use fabric softener. Softener coats the fibres and reduces how much water the terry can pick up. This is the single most common reason a perfectly good head stops working.

Dry fully, and dry off the floor. Store heads head-up or hanging so air reaches the strips.

Retire the head when the strips flatten, mat together, or start leaving a film on the floor - that is the wear point, not the first stain.

Customisation and wholesale

Item Options
Weight 150 g – 350 g, any weight in the range
Colour Matched to your colour reference
Material 100% polyester or polyester-nylon blend
Thread / socket Italian thread, French thread, others on request
End type Cut end (this product) or loop end
Packaging [YOUR PACKAGING OPTIONS]
Private label [YOUR OEM / LABEL / BARCODE POLICY]
MOQ [MOQ]
Sample lead time [SAMPLE LEAD TIME]
Bulk lead time [BULK LEAD TIME]

Frequently asked questions

What is a cut-end mop head?
A cut-end mop head is made from strips of fabric that are cut at the ends rather than looped. The cut ends let each strip move independently and follow grout lines and uneven floors. Cut-end heads can shed a small amount of loose fibre in the first few washes, then settle.
How do I know if I need an Italian thread or a French thread?
Unscrew your current mop head and look at the thread on the handle. Italian thread and French thread are different fittings and are not interchangeable. If you are unsure, send us the thread diameter of your handle and we will match the head to it.
Can I order a weight that is not listed?
Yes. The head is made to order anywhere between 150 g and 350 g. Any weight in that range is possible.
Can I choose the colour?
Yes - heads are made in the colour you specify, so you can run colour-coded cleaning by area.
Is this head cotton or microfibre?
Neither. This head is polyester terry towelling, in either 100% polyester or a polyester-nylon blend.
Which lasts longer, a polyester terry mop head or a cotton one?
Used in the same conditions, polyester terry generally outlasts cotton: polyester keeps its strength when wet, dries faster and resists the mildew that breaks down cotton left damp. Cotton still picks up more water per gram.
How should I wash and store it?
Rinse in clean water after each shift, wash warm, avoid fabric softener, and dry the head fully and off the floor.
Will it fit mop handles I already own?
If your handle takes an Italian thread, French thread or another thread we can supply, yes. Check your handle's thread before ordering, or send us the diameter.

 

Hot Tags: wet mop head in polyester terry towel strips with custom 150-350g weight for daily floor cleaning in hotels and supermarkets, China, manufacturers, suppliers, factory, price, 360 Spin Mop Refill, Microfiber Loop Mop, Microfiber Mop Refill, Mop Connector, Mop Handle, Towel Mop

Send Inquiry